|
Post by bigfuninc on Feb 12, 2017 11:21:10 GMT -5
Looking for a drivers side body section for a Bradley 1.Previous owner did a real bad repair job after an accident.Would buy whole body that is in bad shape.Hate to wrck a good body.Live in Pacific Northwest.Thanks
|
|
|
Post by bigfuninc on Nov 7, 2016 9:49:20 GMT -5
There are two "Plywood" compartments fiberglassed into each side of my Bradley..Right at the door.One is destroyed by rot and accident damage.Are both side the same sizes from factory?Are these compartments factory?I want to use the passenger side as a template for drivers side.The body panel has moved out due to the missing compartment.I have not seen this discussed on any forum...Need expert opinion.Thanx Dan
|
|
|
Post by bigfuninc on Mar 19, 2015 9:13:49 GMT -5
Sent you e-mail interested.
|
|
|
Post by bigfuninc on Feb 25, 2014 8:21:58 GMT -5
I'm interested also.Where R U located?
|
|
|
Post by bigfuninc on Dec 15, 2013 10:40:11 GMT -5
Thank you.Wish I had looked a little closer at the time installation I could have adjusted the fuel tanks neck some..I`m going to try making an aluminum spacer to lift the filler neck up a bit and shorten the filler neck an inch..I have a couple proper fuel hoses with 90 degree bents that might work. definitely be slow filling
|
|
|
Post by bigfuninc on Dec 14, 2013 10:23:51 GMT -5
Having problem aligning filler neck and fuel tank pipe on my Bradley 1. Any suggestions?
|
|
|
Post by bigfuninc on Nov 27, 2013 9:48:20 GMT -5
yes.That's where I put mine also. I got a vent/valve from my local marina. Lets gas vents out but won't let water in.I have to change the vent fitting to allow for the larger sized vent hose.
|
|
|
Post by bigfuninc on Nov 24, 2013 12:02:14 GMT -5
Where is the proper location for the fuel-tank exterior vent on a Bradley 1?i was thinking inside the rear tire well?Thanx
|
|
|
Post by bigfuninc on Aug 27, 2013 7:55:17 GMT -5
Wow.nice
|
|
|
Post by bigfuninc on Aug 26, 2013 5:09:39 GMT -5
There is always a way...PM sent!
|
|
|
Post by bigfuninc on Aug 25, 2013 9:44:09 GMT -5
There are ways around the RIV import rules...expensive. .Check kijiji(sp) Alberta .there was a couple there.Dan
|
|
|
Post by bigfuninc on Jun 20, 2013 7:21:26 GMT -5
The continuing project Attachments:
|
|
|
Post by bigfuninc on May 4, 2013 8:41:19 GMT -5
bigfuninc@shaw.ca I can pick-up
|
|
|
Post by bigfuninc on May 2, 2013 8:03:47 GMT -5
Complete body only or with pan?Got a picture
|
|
|
Post by bigfuninc on Apr 14, 2013 9:10:59 GMT -5
very nice thanks.i have not seen a lot of Bradley motor compartments
|
|
|
Post by bigfuninc on Apr 13, 2013 10:16:22 GMT -5
thanks.Gives a starting point
|
|
|
Post by bigfuninc on Apr 13, 2013 9:08:54 GMT -5
Any pictures around of the cold side/hot side divided up on a Bradley 1?i looked at mine and does not look like an easy project?Are you referring to the stock engine tin complete?
|
|
|
Post by bigfuninc on Mar 29, 2013 9:42:28 GMT -5
Thanks for the info.i have a place it would fit,I can build a mount that will allow air flow.not sure if I will use it.On the buggies I have built it was standard equipment.
|
|
|
Post by bigfuninc on Mar 28, 2013 6:09:22 GMT -5
The best advise I could give is for you to purchase Jeff Troy's CD about Bradley GT 1.Unbelievable amount of info in it.He is a member here
|
|
|
Post by bigfuninc on Mar 27, 2013 8:22:03 GMT -5
Thanks.I believe you are right.
|
|
|
Post by bigfuninc on Mar 26, 2013 9:52:03 GMT -5
Thanks.I'm running a 1641,The oil cooler came with the car.looking around I did not see many mounted into Bradley's
|
|
|
Post by bigfuninc on Mar 25, 2013 7:09:06 GMT -5
What remote oil cooler are you using and where did you mount it?I 'm thinking mounting mine under-side of the rear seat.Your thoughts?
|
|
|
Post by bigfuninc on Feb 27, 2013 9:16:59 GMT -5
Watch what your buying and how the "Bill of Sale"is written .Our glorious RIV program has very defined rules concerning importing "Kit-cars"into Canada
|
|
|
Post by bigfuninc on Feb 19, 2013 9:02:16 GMT -5
Thank you,I did look at your CD and seen that.I have this "H" shaped bracket that fits nice will be great added front protection,I can put JSPtown's idea to work also.
|
|
|
Post by bigfuninc on Feb 18, 2013 11:01:14 GMT -5
Great. thank you.gives me something too think about.
|
|
|
Post by bigfuninc on Feb 18, 2013 10:39:34 GMT -5
I have a lot of front body vibration,Will the bumper mounts cure this or do I have parts missing?I have an "H" shaped structure,that came with my car, that bolts to the front frame head and u-bolted to the front beam but does not come close to the actual body.It looks more more protection than a actual "Bradley " part.
|
|
|
Post by bigfuninc on Feb 16, 2013 10:25:41 GMT -5
check out Craigslist Bellingham.There is one up there occasioanlly for sale.Also was one in Puolsbo.Chck out "search tempest"
|
|
|
Titles
Feb 2, 2013 13:43:23 GMT -5
Post by bigfuninc on Feb 2, 2013 13:43:23 GMT -5
I knew about these problems also.BUT my car is legally in Canada and I have registered and insured it.Took about 6 weeks. I would use them again.
|
|
|
Titles
Feb 2, 2013 10:46:43 GMT -5
Post by bigfuninc on Feb 2, 2013 10:46:43 GMT -5
When I was trying to get my Avenger into Canada,I found a company called "Interntional Title Services" 702-435-8371 Belive "Joe" did the job.NO stress service.I have my Avenger in BC CANADA in my name totally legal.Fantstic service.
|
|
|
Post by bigfuninc on Jan 3, 2013 7:55:01 GMT -5
Thanks for the info.Yes local truck shop did the trick.Wanted too stay away from LED lights look great but going for an original look.Dan
|
|