|
|
Post by jman on Jul 28, 2014 7:22:31 GMT -5
How's it going? Does anyone know of anywhere that makes replica body tags for a bradley GT?
|
|
|
|
Post by skip20 on Jul 28, 2014 7:33:15 GMT -5
How's it going? Does anyone know of anywhere that makes replica body tags for a bradley GT? What replica body tags? |
|
|
|
Post by jman on Jul 28, 2014 8:16:54 GMT -5
The one that has the body identification number on it mine is so far gone there is nothing on it anymore
|
|
|
|
Post by skip20 on Jul 28, 2014 9:12:55 GMT -5
The one that has the body identification number on it mine is so far gone there is nothing on it anymore Is it a Bradley Tag, if so it may have been a turn key. Is it the State Tag, which will have the State Insp. on it w/ a serial # Have you gotten it Reg in your State yet? |
|
|
|
Post by jman on Jul 28, 2014 10:23:09 GMT -5
It's register as a bradley but if I ever ran into the wrong cop there are no #'s on it
|
|
|
|
Post by skip20 on Jul 28, 2014 11:26:55 GMT -5
It's register as a bradley but if I ever ran into the wrong cop there are no #'s on it Picture of tag?  |
|
|
|
Post by Big-birds-ride on Jul 28, 2014 12:36:52 GMT -5
As far as I know, only complete builds by Bradley came with body tags. As far as the VW pan under the fiberglass body, the VW pan Vehicle ID Number can typically be found on the center hump where the shifter and emergency brake are located. The number is stamped into the hump towards the rear where the hump begins to spread out towards the sides of the body pan. About 2 inches from where it starts to spread out is where the VIN number would be stamped into the body pan.
|
|
|
|
Post by horen2tas on Jul 28, 2014 16:39:33 GMT -5
Here are two possibilities of what you are referring to Both are easily fabricated from a created pixel or vector line file   |
|
|
|
Post by jman on Jul 28, 2014 17:48:40 GMT -5
The top one that is blank so I can stamp my number in . That's the what they used as the vin for my title
|
|
|
|
Post by skip20 on Jul 28, 2014 20:36:04 GMT -5
The top one that is blank so I can stamp my number in . That's the what they used as the vin for my title I can Laser them out for you, in fact I was suppose do one for horen2tas in S/S & never got around to it. |
|
|
|
Post by horen2tas on Jul 28, 2014 22:32:04 GMT -5
Copy and save this file @ 4" width by 1.5" height onto a disc or a thumb drive  then either contact Skip or go to a trophy shop with it and have a brushed metal plate burned with the image |
|
|
|
Post by jman on Jul 29, 2014 5:30:38 GMT -5
Never thought of a trophy company I'll give that a try thanks
|
|
|
|
Post by jman on Aug 1, 2014 11:54:05 GMT -5
Well had my tag done at a trophy shop came out pretty good never would have thought to go there thanks
|
|
|
|
Post by horen2tas on Aug 1, 2014 12:29:37 GMT -5
Great! Glad it worked out.
I should get it together and make up the other tag for download>
all the best,
Mike Horen
|
|
|
|
Post by skip20 on Aug 1, 2014 13:22:42 GMT -5
Great! Glad it worked out. I should get it together and make up the other tag for download> all the best, Mike Horen Don't do it as a .JPG! .EPS would be better so it can be edited. |
|
|
|
Post by dawgdk on Aug 1, 2014 14:26:53 GMT -5
Post a picture of the new Tag for us all to see. Others might want to go this route also.
|
|
|
|
Post by horen2tas on Aug 1, 2014 16:01:58 GMT -5
Great! Glad it worked out. I should get it together and make up the other tag for DOWNLOAD (as in for everyone)all the best, Mike Horen That was my intention, I have enough of them for my own use so I'd make it available for the board to copy and paste like I did with the one above Next project we should do the license plate frame with a 3D printer how 'bout that Skip? |
|
|
|
Post by skip20 on Aug 1, 2014 17:51:56 GMT -5
Great! Glad it worked out. I should get it together and make up the other tag for DOWNLOAD (as in for everyone)all the best, Mike Horen That was my intention, I have enough of them for my own use so I'd make it available for the board to copy and paste like I did with the one above Next project we should do the license plate frame with a 3D printer how 'bout that Skip? I could get them made in China cheap. I have connections! Need the tag in CDR or EPS so I can edit it for # & add the GTII |
|
